Top 22 Waterway Pumps for 2019

 

Waterway Pump Union 1 fbt x 1 s 400-1990

Waterway Pump Union, 1″ fbt x 1″ s #400-1990

Waterway Pump Union, 1″ fbt x 1″ s #400-1990 - Waterway pump. Made in the usa. Pump union, 1″ female buttress thread x 1″ slip #400-1990.

 

Waterway 310-1750 2&quot Executive 56 Frame 5hp Wet End Pump

Waterway 310-1750 2" Executive 56 Frame 5hp Wet End Pump

Waterway 310-1750 2" Executive 56 Frame 5hp Wet End Pump - Outside dimension of the front face plate measures 7-1/2″. 50 hp executive wet end complete 56 frame 2″ x 2″. 2″ x 2″ inlet and outlet (2″ measures 3″ outside diameter).

 

Waterway Workhorse Pump 6&quot Trap Body 15&quotfpt 15&quotbtrs X 2&quotunion Flange 319-2170

Waterway Workhorse Pump 6" Trap Body 1.5"fpt/ 1.5"btrs X 2"union Flange 319-2170

Waterway Workhorse Pump 6" Trap Body 1.5"fpt/ 1.5"btrs X 2"union Flange 319-2170 - 15″ mbt/15″ fpt x 2″ flange.

 

Waterway Executive 5HP Impeller 1000 Seal Pump Wet End Hot Tub Spa How To Video

Waterway Executive 5HP Impeller 1000 Seal Pump Wet End Hot Tub Spa How To Video

Waterway Executive 5HP Impeller 1000 Seal Pump Wet End Hot Tub Spa How To Video - Note a 115v motor that uses a 1 hp impeller would show about 11-12. To determine the hp refer to the chart below. Visit our store as we also offer these and other associated products and accessories for your spa. The 1-3hp wear rings are larger than the 4-5hp wear rings. See chart below for other horsepowers. This is (1) impeller (1) seal (1) tube silicone & a seal install tool only choose with care, i do not accept returns so be sure these are correct before ordering i do offer free shipping within the lower 48 united states. This kit is features a 5hp impeller and 1000 seal with silicon and a seal install tool that fits an executive 48 frame wet end up to 5hp motor and a 56 frame wet end 5hp motor. Please note the hot tub professor offers how to installation videos on seals and impellers on youtube “hot tub pump wet end seal how to video american spa parts seals” and “spa hot tub waterway pump wet end seal repair how to video”. I would advise replacing the seal when you replace the impeller. The difference between a 48 or 56 frame wet end is the spacing of the motor thru bolts. We offer a seal and silicone in a kit or an impeller individually, and the purpose of this kit is to repair a damaged impeller and seal inside the wet end. 0 amps on high speed a 230v motor would show about 8. Do not choose a larger impeller thinking that it will make your hot tub stronger it will only damage the motor and make it run hot on high speed as well as there are (2) different size wear rings on the impellers so if you choose a different size impeller your wear ring may not work. 0 amps on high. The 48 frame will be 3 5/8″ between or 5 3/16″ in a x. A 5hp would be 16a, 4hp = 14a, 3hp = 12a, 2hp = 10a, 1hp = 8a. This impeller fits between the face and the volute of an executive wet end.

 

Waterways Clearwater II 75 sqft w 1 hp 2-speed pump complete cartridge filter system

Waterways Clearwater II 75 sq.ft. w/ 1 h.p. 2-speed pump. complete cartridge filter system

Waterways Clearwater II 75 sq.ft. w/ 1 h.p. 2-speed pump. complete cartridge filter system - Comes with a 75 sq ft waterway plastics fiber filter for ultimate swimming pool water filtration. 1 1/2″ filter connections. Filter connection hoses/clamps to swimming pool / water return are not included. Standard 1/5″ pvc connections makes it easy to connect to standard above ground pool hose or use pvc pipe instead for the ultimate connection. Comes with a 1 hp, 2 speed waterway pump and motor.

 

Waterway SMF110 1HP Single Speed 115208-230V SMF Pump

Waterway SMF110 1HP Single Speed 115/208-230V SMF Pump

Waterway SMF110 1HP Single Speed 115/208-230V SMF Pump - Waterway smf-110 in ground swimming pool pump 1-hp, single speed. Features  •  super quiet operation  •  2-inch unionized (intake/discharge)  •  one piece pot and volute reduce noise  •  lower flow rates for more versatile installations. 60-hertz. Self-priming, large trap and leaf basket. Ships with pump unions for 2-inch pvc pipe size for outdoor operation. Super quiet, efficient, and self-priming.

 

Spa Hot Tub Waterway Pump Air Bleeder Plug 14 Mpt X 38 Barb Sealer Fitting

Spa Hot Tub Waterway Pump Air Bleeder Plug 1/4″ Mpt X 3/8″ Barb Sealer Fitting

Spa Hot Tub Waterway Pump Air Bleeder Plug 1/4″ Mpt X 3/8″ Barb Sealer Fitting - Filter connection hoses/clamps to swimming pool / water return are not included. Replacement cartridge is ak70018. 1 1/2″ filter connections. Comes with a 2 hp, 2 speed waterway pump and motor. Comes complete with one 200 sq ft waterway plastics fiber filter for ultimate swimming pool water filtration.

 

Waterway Svl56 Csa Supreme Pump Cover Lid 511-1310

Waterway Svl56 Csa Supreme Pump Cover Lid 511-1310

Waterway Svl56 Csa Supreme Pump Cover Lid 511-1310 - 511-1310.

 

Waterway Plastics 3420610-15 48-frame Spa Pump

Waterway Plastics 3420610-15 48-frame Spa Pump

Waterway Plastics 3420610-15 48-frame Spa Pump - Highly versatile wet end can be rotated every 90°. Executive wet end designed specifically for 48-frame motors. Large 2 &frac12 in intake for improved flow performance and reduced noise. Large 6 &frac12 in diameter wet end for higher head pressure. Thermally protected to extend life expectancy of motor.

 

Waterway 310-4030 2 Hp Hi-flo Pump Impeller

Waterway 310-4030 2 Hp Hi-flo Pump Impeller

Waterway 310-4030 2 Hp Hi-flo Pump Impeller - . P. Waterway hi-flo side discharge pump & wet ends, impeller 2 h.

 

Waterway Executive 4HP Impeller 1000 Seal Pump Wet End Hot Tub Spa How To Video

Waterway Executive 4HP Impeller 1000 Seal Pump Wet End Hot Tub Spa How To Video

Waterway Executive 4HP Impeller 1000 Seal Pump Wet End Hot Tub Spa How To Video - The 1-3hp wear rings are larger than the 4-5hp wear rings. The difference between a 48 or 56 frame wet end is the spacing of the motor thru bolts. This is (1) impeller (1) seal (1) tube silicone & a seal install tool only choose with care, i do not accept returns so be sure these are correct before ordering please be aware that the replacement impeller that you receive will not look like the one in the picture, that has been discontinued by the manufacturer and the new one works completely fine but looks very different. I do offer free shipping within the lower 48 united states. Please note the hot tub professor offers how to installation videos on seals and impellers on youtube “hot tub pump wet end seal how to video american spa parts seals” and “spa hot tub waterway pump wet end seal repair how to video”. Note a 115v motor that uses a 1 hp impeller would show about 11-12. See chart below for other horsepowers. I would advise replacing the seal when you replace the impeller. A 5hp would be 16a, 4hp = 14a, 3hp = 12a, 2hp = 10a, 1hp = 8a. To determine the hp refer to the chart below. This kit is features a 4hp impeller and 1000 seal with silicon and a seal install tool that fits an executive 48 frame wet end up to 5hp motor and a 56 frame wet end 4hp motor. The purpose of this kit is to repair a damaged impeller and seal inside the wet end. Do not choose a larger impeller thinking that it will make your hot tub stronger it will only damage the motor and make it run hot on high speed as well as there are (2) different size wear rings on the impellers so if you choose a different size impeller your wear ring may not work. It fits between the face and the volute of an executive wet end. 0 amps on high. 0 amps on high speed a 230v motor would show about 8. Visit our store as we also offer these and other associated products and accessories for your spa. The 48 frame will be 3 5/8″ between or 5 3/16″ in a x.

 

Waterway Plastics Ph1100-6 Hi-flo 1 Hp Side Discharge Above Ground Pool Pumpamp Trap

Waterway Plastics Ph1100-6 Hi-flo 1 Hp Side Discharge Above Ground Pool Pump & Trap

Waterway Plastics Ph1100-6 Hi-flo 1 Hp Side Discharge Above Ground Pool Pump & Trap - On and off switch on bottom of motor cover. Dimension, 10875 l x 7625 w x 24375 h in. Hi-flo side discharge. 1 hp, 1-speed, 98 amps, 115v 60hz, automatic overload protection.

 

Waterway 3410020-1E 0125HP 230V Single Speed Spa Pump

Waterway 3410020-1E 0.125HP 230V Single Speed Spa Pump

Waterway 3410020-1E 0.125HP 230V Single Speed Spa Pump - Delivers 40 gallons per minute. 48 frame proven design. 230 volts. Side discharge for optimum flow. 24 hour circulation pump.

 

Waterway 5 Hp Impeller Executive 56-frame Pump 310-4180

Waterway 5 Hp Impeller Executive 56-frame Pump 310-4180

Waterway 5 Hp Impeller Executive 56-frame Pump 310-4180 - 310-4180.

 

Waterway Plastics Ph2150-6 15 Hp 2-speed 34501725 Rpm 115v Above Ground Pool Pump With Large Debri

Waterway Plastics Ph2150-6 1.5 Hp 2-speed 3450/1725 Rpm, 115v Above Ground Pool Pump With Large Debri

Waterway Plastics Ph2150-6 1.5 Hp 2-speed 3450/1725 Rpm, 115v Above Ground Pool Pump With Large Debri - 15 hp 2-speed above ground swimming pool pump and motor. Waterway plastics is proud to design, engineer and produce our quality line of products right here in the use. Very large hair & lint trap. Rpm rating 3450 high / 1725 low speed.

 

Waterway Plastics 3722021-1d Executive 56 Frame 5 Hp Spa Pump 230-volt

Waterway Plastics 3722021-1d Executive 56 Frame 5 Hp Spa Pump, 230-volt

Waterway Plastics 3722021-1d Executive 56 Frame 5 Hp Spa Pump, 230-volt - 220 gallons per minute flow rate. 56-frame motor for added strength, cooler operating temperature and longer motor life. Highly versatile wet end can be rotated every 90 degrees. Viton shaft seals.

 

Waterway 3721621-1V 25 x 25 40HP 230V 2-Speed 56 Fame Viper OEM Pump

Waterway 3721621-1V 2.5″ x 2.5″ 4.0HP 230V 2-Speed 56 Fame Viper OEM Pump

Waterway 3721621-1V 2.5″ x 2.5″ 4.0HP 230V 2-Speed 56 Fame Viper OEM Pump - Two speed motors have four sets of insulated windings for increased efficiency. Large 2-1/2″ intake for improved flow performance and reduced noise. Viper wet end designed specifically for 56-frame motors. 56-frame motor for added strength, cooler operating temperature, and longer motor life. Two double shielded ball bearings with moisture resistant grease for quieter operation and longer life.

 

2 Bearing 1000 Seal Pump Parts Kit Waterway Spa Hot Tub Pumps How To Video

(2) Bearing & 1000 Seal Pump Parts Kit Waterway Spa Hot Tub Pumps How To Video

(2) Bearing & 1000 Seal Pump Parts Kit Waterway Spa Hot Tub Pumps How To Video - Bearing tools not included note this seal fits waterway executive, hi-flo, spa flo, iron might, 1 1/2″ center discharge, e series and workman pump wet ends to install you should put silicon sealant on the back of the metal part and gently push it into place with the included seal install tool. Also the rubber part can use a light coat of silicon to slide it into place in the impeller. Visit our store as we also offer these and other associated products and accessories for your spa. The bearing are standard fit for most motors with waterway wet ends. Please note the hot tub professor offers how to installation videos on seals and impellers on youtube “hot tub pump wet end seal how to video american spa parts seals” and “spa hot tub waterway pump wet end seal repair how to video”. Note installing bearings requires special tools and special knowledge therefore this kit is not for someone who has never installed bearings before. This seal is used in waterway wet ends only look in our store for other seal & bearing kits. Choose with care, i do not accept returns so be sure these are correct before ordering i do offer free shipping within the lower 48 united states. The hole in both parts is about 5/8″. We offer these seals alone and/or with the professor’s silly juice and/or with an impeller in a kit so look in our store. It is 1 3/8″ across the back of the spring seal part that goes into the volute or wetend back and the ceramic & rubber part that goes into the impeller is 1 1/4″. You are buying a kit that features (1) ps-1000 seal and (2) bearings that fit most motors that are mated to waterway pump wet ends, the professor silly juice to seal the seal and a tool to push the seal into place.

 

Waterway Plastics 315-1220B Executive 56 Frame Spa Pump Volute

Waterway Plastics 315-1220B Executive 56 Frame Spa Pump Volute

Waterway Plastics 315-1220B Executive 56 Frame Spa Pump Volute - Fits waterway pump volute, executive 56 frame w/inserts (verify frame). Manufacturer waterway plastics is proud to design, engineer & produce our quality line of products right here in the usa.

 

Waterway Plastics Champs-115 15 Hp 3450 Rpm 115230v No Champs 115 In Ground Swimming Pool Pump Champion

Waterway Plastics Champs-115 1.5 Hp 3450 Rpm 115/230v No. Champs 115 In Ground Swimming Pool Pump Champion

Waterway Plastics Champs-115 1.5 Hp 3450 Rpm 115/230v No. Champs 115 In Ground Swimming Pool Pump Champion - Plumbing inlet/outlet = 2″. High head pressure pump, self priming. 1 year manufacture warranty. 15 hp 3450 rpm, 160/70 amps, 115/230v 60hz 1-speed. Large debris basket with see thru cover.

 

Waterway Executive 3HP Impeller 1000 Seal Pump Wet End Hot Tub Spa How To Video

Waterway Executive 3HP Impeller 1000 Seal Pump Wet End Hot Tub Spa How To Video

Waterway Executive 3HP Impeller 1000 Seal Pump Wet End Hot Tub Spa How To Video - Visit our store as we also offer these and other associated products and accessories for your spa. To determine the hp refer to the chart below. Note a 115v motor that uses a 1 hp impeller would show about 11-12. 0 amps on high. The 48 frame will be 3 5/8″ between or 5 3/16″ in a x. This is (1) impeller (1) seal (1) tube silicone & a seal install tool only choose with care, i do not accept returns so be sure these are correct before ordering i do offer free shipping within the lower 48 united states. See chart below for other horsepowers. 0 amps on high speed a 230v motor would show about 8. I would advise replacing the seal when you replace the impeller. We offer a seal and silicone in a kit or an impeller individually, and the purpose of this kit is to repair a damaged impeller and seal inside the wet end. Please note the hot tub professor offers how to installation videos on seals and impellers on youtube “hot tub pump wet end seal how to video american spa parts seals” and “spa hot tub waterway pump wet end seal repair how to video”. The difference between a 48 or 56 frame wet end is the spacing of the motor thru bolts. Do not choose a larger impeller thinking that it will make your hot tub stronger it will only damage the motor and make it run hot on high speed as well as there are (2) different size wear rings on the impellers so if you choose a different size impeller your wear ring may not work. A 5hp would be 16a, 4hp = 14a, 3hp = 12a, 2hp = 10a, 1hp = 8a. This impeller fits between the face and the volute of an executive wet end. The 1-3hp wear rings are larger than the 4-5hp wear rings. This kit is features a 3hp impeller and 1000 seal with silicon and a seal install tool that fits an executive 48 frame wet end up to 4hp motor and a 56 frame wet end 3hp motor.

 

Waterway Plastics 805-0439 Lid O-ring Svl56 Pump

Waterway Plastics 805-0439 Lid O-ring Svl56 Pump

Waterway Plastics 805-0439 Lid O-ring Svl56 Pump - Manufactured to the highest standards to provide you with a quality product. Best value for your money. Lid o-ring svl56 pump.